How do I clean my dryer vent?
Clean the lint screen, then unplug the dryer and pull it out so you can clear the duct behind it, the pipe in the wall and the hood outside. Replace a foil or plastic duct with metal. If the run is long or goes up to the roof, call a pro. I'll remind you when it's time.
Quick steps
- Pull the lint off the screen by hand.
- Unplug the dryer and pull it out, leaving room to work behind it.
- Check the short duct between the dryer and the wall. Swap foil or plastic for metal.
- Clear the lint out of the duct with a brush and a vacuum hose.
- Vacuum behind and under the dryer.
- Go outside and check the hood. The flap should swing free.
- Put it all back, plug it in and run an empty cycle.
The longer version
Your dryer pushes hot, wet air out of the house. Lint rides along with it. Some of that lint stays behind in the pipe, and it adds up.
Marcus in McKinney noticed his towels needed a second cycle. He figured the dryer was getting old. Longer drying times are a sign the vent needs cleaning, according to the NFPA. He unplugged the dryer, pulled it out, cleaned the duct, and ran a normal load.
Why it matters here
Lint is fuel, and the numbers show it. A U.S. Fire Administration report on 2008 to 2010 data counted about 2,900 clothes dryer fires in homes a year, with about 5 deaths, about 100 injuries and about $35 million in property loss. Failure to clean was the leading factor, at 34 percent of the fires. January was the peak month, with 11 percent.
These are national figures, and they're a bit old. The NFPA says the same thing, that failure to clean is the leading cause of home fires involving dryers and washers.
Each step, explained
The lint screen
The lint screen is the flat mesh tray you slide out near the door or on top of the dryer. The CPSC says to clean it before or after every load. Never run the dryer without it.
Pull the lint off by hand. Whirlpool says to skip water on the regular cleaning, because wet lint is harder to remove. Whirlpool also says that buildup from detergent and fabric softener on the screen can lengthen drying time. For a deeper clean, Whirlpool says to wash it with hot water, liquid detergent and a nylon brush, then dry it thoroughly before it goes back in.
The short duct behind the dryer
The short, bendy pipe from the back of the dryer to the wall is the transition duct. This is where the most trouble hides. The CPSC says to replace plastic or foil accordion-style duct with rigid or corrugated semi-rigid metal duct. Those soft ducts trap lint more easily and are more likely to kink or crush, which cuts airflow.
The U.S. Fire Administration adds that building codes call for metal vents with smooth interiors, and that flexible transition ducts shouldn't be longer than 8 feet. GE no longer approves plastic duct, and the company says its bends can narrow below 4 inches and let lint build up.
Before you pull the dryer out, unplug it. Whirlpool says to leave about a foot of space behind it so you have room to work. That's a good grandpa habit. Ask someone to help you move it.
The duct in the wall
The pipe that runs through the wall to the outside is the wall duct. Whirlpool's steps are to unscrew the clamps or remove the tape at the back, then pull large lint out by hand, run a dryer cleaning brush through the duct and vacuum with a hose attachment.
The CPSC notes you may need to disconnect the duct to clear a blockage, and you must reconnect it before you use the dryer again.
The outside hood and its flap
Walk outside and find the vent cover on the siding. That's the hood, and the little door inside it is the flap. It opens when the dryer runs and closes when it stops. The NFPA says the flap should open while the dryer runs and not be blocked.
Here's a simple check. Start the dryer and hold your hand near the hood. The CPSC says exhaust should be coming out the outside vent, and if it isn't, the vent or duct may be blocked. Whirlpool says to keep the hood free of lint so the flapper or louvers can open and close fully. GE says no screen or grid should cover the opening. A screen traps lint.
Behind and under the dryer
Lint doesn't only go out the vent. The CPSC says lint collects behind the dryer, so clean that area and keep it clear of clutter. While the dryer is pulled out, run the vacuum along the floor, the wall and the back panel. The same CPSC page says a qualified service person should clean the inside of the dryer itself.
Put it back and test it
Reattach the duct with the clamps, plug the dryer in and push it back without crushing the duct. Then run an empty cycle. Whirlpool says to run it for 10 to 15 minutes to clear remaining dust. Check the hood outside once more.
Signs of a clog
The signs are easy to spot. Clothes come out damp after a normal cycle, or a load takes noticeably longer. The CPSC says either can mean a blocked lint screen or exhaust duct. Whirlpool's venting guide lists a hot dryer top among the signs. The Building America program at Pacific Northwest National Laboratory adds clothes or the dryer running hot, or a burning smell.
What people get wrong
Cleaning only the lint screen is the most common mistake. The screen catches some lint, and the rest goes down the duct. Clear the duct and the hood as well.
Keeping a foil or plastic duct because it still fits is the second one. It will fit, but metal moves air better. Swap it for rigid or semi-rigid metal.
Putting a screen over the hood is a third. It traps lint. Replace a screened hood with one that has a louvered flap, as the Building America guide advises.
The last is squeezing the dryer against the wall. A crushed duct blocks airflow. Leave enough room that the duct keeps its shape.
When to call a pro
A long duct needs a pro. The Building America guide says the total run should be 35 feet or less, and shorter if the maker says so, and each bend subtracts from that. Whirlpool says to follow the maximum length in your dryer's installation instructions. If the duct is long, runs upward or goes through the roof, have a pro look at it. The sources disagree on roof venting, since GE allows it and the Building America guide recommends an outside wall. That's a good reason to get a professional opinion. Stay off the roof yourself.
If you have a gas dryer, the NFPA says to have a professional confirm the gas line and connections are intact and leak-free. Whirlpool says gas dryers should be installed by a qualified installer or service agency. Gas work and electrical work belong to a licensed pro. Call one if you can't reach the duct or the dryer still runs hot after you clean.
Sources
- U.S. Fire Administration, Clothes Dryer Fires in Residential Buildings (Aug 2012). Checked Nov 20, 2026.
- U.S. Consumer Product Safety Commission, Clothes Dryers publication 5022. Checked Nov 20, 2026.
- National Fire Protection Association, Dryer and Washer Safety Tips (hosted by the U.S. Department of Energy). Checked Nov 20, 2026.
- Building America Solution Center (U.S. Department of Energy), Proper Clothes Dryer Venting. Checked Nov 20, 2026.
- Whirlpool, How to Clean a Dryer Vent. Checked Nov 20, 2026.
- Whirlpool, Dryer Venting Requirements (W11222085). Checked Nov 20, 2026.
- GE Appliances, Dryer Installation Information for Exhaust Ducting. Checked Nov 20, 2026.
I'll remind you when it's time.
Sign up, and I'll send you the job when your house needs it, with a short guide.
Reminders by text and email when your house needs them.
General information only, not a substitute for a licensed pro.
