My Home Mentor home page

Guides

How do I change my AC and heater air filter?

Turn the system off at the thermostat, slide out the old filter, and put in a new one the same size with the arrow pointing toward the blower. The size is printed on the cardboard frame, and the arrow should point into the duct. A gray, dusty filter is ready to go.

Quick steps

  1. Turn the system off at the thermostat.
  2. Find the filter, either behind a big return grille or in a slot at the air handler.
  3. Slide the old filter out and read the size printed on its frame.
  4. Check the arrow on the new filter. It points toward the blower, into the duct.
  5. Slide the new filter in, close the grille or slot cover, and turn the system back on.
  6. Write the date on the frame so you know when it went in.

The longer version

One flat square of paper and wire sits between your family and a lot of dust. It also decides how hard your AC and furnace have to work. Most people never look at it.

Marcus in McKinney noticed his AC running and running without cooling the house the way it used to. The filter had turned gray and packed with dust, and Carrier says restricted airflow can lead to a frozen evaporator coil, the part that cools the air. He swapped in a new filter the same size. If you see ice on the indoor unit, turn the system off and call a pro.

Why it matters here

A clogged filter costs you money. The Department of Energy says that regularly replacing or cleaning filters can lower an air conditioner's energy use by 5 to 15 percent. ENERGY STAR adds that a dirty filter makes the system work harder, raises energy costs and can lead to early equipment failure.

Hot, humid weather makes it worse. A Department of Energy guide says that when a filter is too restrictive in that kind of climate, supply air can get too cold, ducts in a hot attic can sweat, and the coil can ice up. If your ducts run through the attic, that matters here.

Each step, explained

Turn the system off

Set the thermostat to Off. ENERGY STAR says to turn off the furnace, AC and fan before you pull the filter out. You can also use the breaker panel or a switch at the unit. This takes a few seconds.

Find the filter

There are two usual spots. The first is behind a large return grille, about 20 by 25 inches, in a ceiling, wall or floor. Some homes have one per floor. The return grille is the big vent that pulls air in, not the small ones that blow air out.

The second spot is a slot at the air handler, the indoor unit with the blower. According to a Department of Energy Building America guide, the slot sits between the return duct and the air handler or in the first few feet of the return duct. The unit may be in a utility room, basement, crawlspace, attic or garage. The slot cover can be held by thumb screws, clips, a latch or a magnet.

If your filter is in the attic, take a ladder and a flashlight with you.

Read the size on the frame

Look at the cardboard edge of the old filter. The length, width and MERV rating are printed there. MERV is a number for how small a particle the filter catches, and the scale runs from 1 to 20.

The size printed large on the frame can be a rounded, nominal one. The same guide says to check the actual dimensions too. If the old filter doesn't fit well, measure the slot. A good fit covers the whole duct opening and lies flat, not at an angle.

Snap a photo of the printed size with your phone. Then you have it at the store.

Thin filters and thick filters

Most homes have a thin filter about 1 inch deep. A Department of Energy guide says most central systems have filter boxes sized for a standard 1-inch fiberglass filter. Some homes have a thick media filter instead, a deep, pleated one that sits in its own cabinet. Carrier describes these as 3 to 5 inches thick and lasting longer than a 1-inch filter.

Deeper pleats give the air more filter to move through. One example from the Department of Energy shows a 4-inch filter lets air through more easily than a 1-inch filter of the same MERV rating. Even so, don't force a thick filter into a thin slot. A larger filter may need changes to the slot itself, and that's a job for a pro.

Point the arrow and slide it in

Every filter has an arrow printed on the frame. ENERGY STAR says the arrows should always point toward the furnace or blower unit. Put another way, the arrow follows the air as it travels into the system. Backward matters too. Carrier says a filter put in backward can restrict airflow quickly.

Take off the plastic wrap but keep the cardboard frame. The guide warns that the wire over the filter fabric can be very sharp, so handle it with care. Write today's date on the frame with a marker before it goes in. That's one of the steps in the same guide.

At a return grille, the guide also says to tape the filter's edge to the grille with masking tape so air can't slip around it. At a slot, the cover should fit snugly, but it shouldn't be taped or caulked, so the next change is easy.

Know when it's due

Your eyes are the best tool. Carrier lists these signs that a filter is dirty: it looks gray with dusty buildup, you see more dust on the furniture, heating or cooling takes longer, or you can't remember the last change.

ENERGY STAR also says to check it, and clean or replace it as needed. I'll remind you when it's time to look.

What people get wrong

The biggest mistake is buying the fanciest filter. A high MERV number catches smaller particles, but those filters clog faster and push back harder on the air. The guide says to check with your HVAC company before jumping from a MERV 1 filter to a MERV 13 or higher. Stick with the MERV on your old filter, unless a pro tells you otherwise.

Another is how much a filter slows the air. A Department of Energy guide found that a brand new MERV 8 filter cut airflow by about 7 percent on a system with a PSC fan motor. That was a clean filter, so a dirty one has even more effect.

A third is waiting for the system to complain. A filter that's clogged, collapsed, damp or moldy should go right away, and so should one on a system that bangs when it starts. Too much resistance can lead to an overheated furnace or a burned-out blower motor, the same guide says.

The last one is skipping the air handler's slot cover or leaving a gap. If the filter edge is showing, ENERGY STAR says to seal the gap with duct tape or a magnetic cover.

When to call a pro

Call a licensed HVAC technician if you see ice on the indoor unit, if the slot is too small for the filter you need, or if the system still runs poorly with a clean filter. Anything with the gas furnace itself, like the burners or the vent pipe, is for a licensed pro too. ENERGY STAR says your contractor can show you how to change the filter during a maintenance visit, so ask.

The Home Maintenance MinuteBefore you close the grille, write today's date on the new filter's frame with a marker. Next time you'll know exactly how long it's been in there.

Sources

I'll remind you when it's time.

Sign up, and I'll send you the job when your house needs it, with a short guide.

Sign up for free

Reminders by text and email when your house needs them.

General information only, not a substitute for a licensed pro.